Pins
COTTER PIN - STAINLESS 1/16" X 1/2"
16X12SSCP
- Metal, extended prong type cotter pin.
- Extended prong makes separating the tines easier.
- Used to anchor various assemblies by insertion into a drilled hole of a shaft or pin and spreading the points to hold the assembly in position.
- When used with castle or slotted nuts, it becomes a safety locking device.
- Stainless steel material
- Diameter is 1/16 inch
- Length is 1/2 inch
COTTER PIN - STAINLESS 1/16" X 1"
16X1SSCP
- Metal, extended prong type cotter pin.
- Extended prong makes separating the tines easier.
- Used to anchor various assemblies by insertion into a drilled hole of a shaft or pin and spreading the points to hold the assembly in position.
- When used with castle or slotted nuts, it becomes a safety locking device.
- Stainless steel material
- Diameter is 1/16 inch
- Length is 1 inch
ROLL PIN - PLAIN FINISH 1/8" X 3/4"
1834RP
- Standard single-turned pin with .a longitudinal slot and chamfered ends to facilitate installation.
- Used as locking devices, positioning points, anti-chafing surfaces, shaft, or sleeves for wiring.
- Usage is limited only by your imagination and technological capabilities.
- Spring pins require only a straight drilled hole and may be installed using automatic equipment.
- Reusable.
- Carbon steel, plain finish material
- Diameter is 1/8
- Length is 3/4 inch
COTTER PIN - STAINLESS 3/32" X 1-1/2"
332X112SSCP
- Metal, extended prong type cotter pin.
- Extended prong makes separating the tines easier.
- Used to anchor various assemblies by insertion into a drilled hole of a shaft or pin and spreading the points to hold the assembly in position.
- When used with castle or slotted nuts, it becomes a safety locking device.
- Stainless steel material
- Diameter is 3/32 inch
- Length is 1-1/2 inches
COTTER PIN - ZINC 3/32" X 1-1/4"
332X114CP
- Metal, extended prong type cotter pin.
- Extended prong makes separating the tines easier.
- Used to anchor various assemblies by insertion into a drilled hole of a shaft or pin and spreading the points to hold the assembly in position.
- When used with castle or slotted nuts, it becomes a safety locking device.
- Low carbon steel, zinc plated material
- Diameter is 3/32 inch
- Length is 1-1/4 inches
COTTER PIN - STAINLESS 5/32" X 1-1/2"
532X112SSCP
- Metal, extended prong type cotter pin.
- Extended prong makes separating the tines easier.
- Used to anchor various assemblies by insertion into a drilled hole of a shaft or pin and spreading the points to hold the assembly in position.
- When used with castle or slotted nuts, it becomes a safety locking device.
- Stainless steel material
- Diameter is 5/32 inch
- Length is 1-1/2 inches
HITCH PIN - ZINC .093 DIAMETER, 1-5/8" LENGTH
HP203
- Also known as bridge pins or hairpin cotter pins, these are the most common form of hitch pin retention.
- Steel, zinc plated.
- Used in conjunction with clevis pins and also trailer receivers.
- Wire diameter 0.093.
- Length of 1-5/8 inches.
HITCH PIN - ZINC .042 DIAMETER, 1 LENGTH
HP223
- Also known as bridge pins or hairpin cotter pins, these are the most common form of hitch pin retention.
- Steel, zinc plated.
- Used in conjunction with clevis pins and also trailer receivers.
- Wire diameter 0.042.
- Length of 1 inches.
SNAP PIN 5/16 X 2 1/2 DOUBLE WIRE
XB28-02
- Double wire square handle
- The retainer wire is formed of tempered spring wire and cold-headed shank is of low carbon steel.
- 5/16" diameter
- 2-1/2" grip
BENT HITCH PINS 5/8" DIA. 4" GRIP LENGTH
XB31-057
- Widely used as a quick and simple disconnectd for trailer hitch receivers.
- 5/8" diameter
- 4" grip length
- 2" handle length
LOCKING PINS 1/4 X 2-1/4 SQUARE DOUBLE WIRE
XSNAP-250-2250S
- Double wire square handle
- The retainer wire is formed of tempered spring wire and cold-headed shank is of low carbon steel.
- 1/4" diameter
- 2-1/4" grip
Refine