Pins
ROLL PIN - PLAIN FINISH 1/4" X 1-1/4"
X14114RP
- Standard single-turned pin with .a longitudinal slot and chamfered ends to facilitate installation.
- Used as locking devices, positioning points, anti-chafing surfaces, shaft, or sleeves for wiring.
- Usage is limited only by your imagination and technological capabilities.
- Spring pins require only a straight drilled hole and may be installed using automatic equipment.
- Reusable.
- Carbon steel, plain finish material
- Diameter is 1/4
- Length is 1-1/4 inch
ROLL PIN - PLAIN FINISH 1/4" X 1-3/4"
X14134RP
- Standard single-turned pin with .a longitudinal slot and chamfered ends to facilitate installation.
- Used as locking devices, positioning points, anti-chafing surfaces, shaft, or sleeves for wiring.
- Usage is limited only by your imagination and technological capabilities.
- Spring pins require only a straight drilled hole and may be installed using automatic equipment.
- Reusable.
- Carbon steel, plain finish material
- Diameter is 1/4
- Length is 1-3/4 inch
ROLL PIN - PLAIN FINISH 1/4" X 2-1/4"
X14214RP
- Standard single-turned pin with a longitudinal slot and chamfered ends to facilitate installation.
- Used as locking devices, positioning points, anti-chafing surfaces, shaft, or sleeves for wiring.
- Usage is limited only by your imagination and technological capabilities.
- Spring pins require only a straight drilled hole and may be installed using automatic equipment.
- Reusable.
- Carbon steel, plain finish material
- Diameter is 1/4
- Length is 2-1/4 inches
ROLL PIN - PLAIN FINISH 1/4" X 3"
X143RP
- Standard single-turned pin with .a longitudinal slot and chamfered ends to facilitate installation.
- Used as locking devices, positioning points, anti-chafing surfaces, shaft, or sleeves for wiring.
- Usage is limited only by your imagination and technological capabilities.
- Spring pins require only a straight drilled hole and may be installed using automatic equipment.
- Reusable.
- Carbon steel, plain finish material
- Diameter is 1/4
- Length is 3 inchs
ROLL PIN - PLAIN FINISH 1/8" X 5/8"
X1858RP
- Standard single-turned pin with .a longitudinal slot and chamfered ends to facilitate installation.
- Used as locking devices, positioning points, anti-chafing surfaces, shaft, or sleeves for wiring.
- Usage is limited only by your imagination and technological capabilities.
- Spring pins require only a straight drilled hole and may be installed using automatic equipment.
- Reusable.
- Carbon steel, plain finish material
- Diameter is 1/8
- Length is 5/8 inch
LOCKING PINS 1/4 X 1-3/8 ROUND DOUBE-WIRE
XSNAP-250-1375R
- Shank Length: 1-5/8"
- Effective Length: 1-3/8"
- Round Two Wire Snap Pin
- Diameter: 1/4"
- Low Carbon Steel
- Zinc Yellow
DIAPER PIN .243DIA 5"LENGTH 2-1/4 WIDTH
XSPF2435000B
- Overall Length: 8.86"
- Effective Length: 5"
- Heavy Duty Hard Drawn Spring Wire
- Diameter: .243
- Zinc Clear
- Material: Hard drawn spring wire
HITCH PIN - ZINC .162 DIAMETER 2-3/16 LENGTH
HP205
- Also known as bridge pins or hairpin cotter pins, these are the most common form of hitch pin
- Steel, Zinc plated
- Used in conjuction with clevis pins and also trailer receivers
- Wire diameter .162
- Length of 2-3/16 inches
COTTER PIN - ZINC 3/16" X 4"
X36X4CP
- Metal, extended prong type cotter pin
- Extended prong makes separating the tines easier
- Used to anchor various assemblies by insertion into a drilled hole of a shaft or pin and spreading the points to hold the assembly in position.
- When used with castle or slotted nuts, it becomes a safety locking device
- Low carbon steel, zinc plated material
- Diameter is 3/16"
- Length is 4 inches
COTTER PIN - PLAIN 3/16" X 2-1/4"
X36X214CP
- Metal, extended prong type cotter pin
- Extended prong makes separating the tines easier
- Low carbon steel, zinc plated material
- Diameter 3/16"
- Length is 2-1/4"
ROLL PIN - PLAIN FINISH 5/64" X 3/4"
56434RP
- Standard single-turned pin with a longitudinal slot and chamfered ends to facilitate installation
- Used as locking devices, positioning points, anti-chafing surfaces, shaft or sleeves for wiring
- Carbon steel, plain finish material
- Diameter is 5/16"
- Length is 4-3/4"
LOCKING PINS 1/4 X 2-1/4 SQUARE DOUBLE WIRE
XSNAP-250-2250S
- Double wire square handle
- The retainer wire is formed of tempered spring wire and cold-headed shank is of low carbon steel.
- 1/4" diameter
- 2-1/4" grip
SNAP PIN 5/16 X 2 1/2 DOUBLE WIRE
XB28-02
- Double wire square handle
- The retainer wire is formed of tempered spring wire and cold-headed shank is of low carbon steel.
- 5/16" diameter
- 2-1/2" grip
COTTER PIN - ZINC 1/8" X 2"
18X2CP
- Metal, extended prong type cotter pin.
- Extended prong makes separating the tines easier.
- Used to anchor various assemblies by insertion into a drilled hole of a shaft or pin and spreading the points to hold the assembly in position.
- When used with castle or slotted nuts, it becomes a safety locking device.
- Low carbon steel, zinc plated material
- Diameter is 1/8 inch
- Length is 2 inches
Refine