Screws
SHEET METAL SCREW PHIL PAN HD #8 X 1/4"
8X14P
- A thread forming tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- Phillips Pan Head
- For general applications.
- Can be substituted in most applications for round, truss or binding screws.
- Steel zinc plated.
- Diameter: 8
- Length: 1/4"
$0.00
METAL SCREW PAN HEAD PHILLIPS #10 X 3/4" BLACK OXIDE
X10X34P2
- Sheet Metal Screw
- Phillips Drive
- Pan Head
- Black Oxide
- #10 x 3/4"
$0.00
TEK SCREW HEX WASHER HD #14 X 3/4" STAINLESS
X14X34TS
- A tapping screw with spaced threads and a drill point which drills its own hole
- May be used to attach plywood, soft woods or composition board to metal, or attach metal to metal
- All self-drilling screws offer economical benefits: reduces labor and tooling costs; reduces or eliminates drill bits and taps
- Stainless Steel
- Rockwell hardness C55 minimum
$0.00
MACHINE SCREW SLOT TRUSS HEAD 1/4"-20 X 1/2"
1420X12TH
- A straight shank fastener with external threads designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw.
- Machine screws form a fastening superior in strength to spaced thread screws.
- The truss head has a low rounded top surface with a flat bearing surface greater in area than a round-head screw of the same size.
- Made from AISI 1006-1022 or equivalent steel.
- Zinc plated.
- 1/4-20 diameter.
- Length of 1/2".
- Preferred in applications where minimal clearance exists above the head.
- Truss screws provide a trim, finished assembly appearance.
- Widely used as license plates screws.
$0.00
WOOD SCREW PHILLIPS FLAT HEAD #14 X 2"
14X2FPWS
- A thread forming screw having a gimlet point, and a sharp crested, coarse pitch thread.
- Will produce a mating thread when assembled into wood or other resilient materials.
- Flat head Phillips.
- Zinc plated steel.
- Diameter: 14
- Length: 2"
$0.00
SHEET METAL SCREW OVAL PHIL HD #8 X 3/8" STAINLESS
8X38OP
- A thread forming stainless tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- A countersunk head with a rounded top surface and a cone-shaped bearing surface.
- Preferred over a flat head in conical applications, or when a more decorative finished look is desired.
- The countersunk surface nests into mating countersunk application sites.
- Oval head, phillips drive
- Screw diameter 8
- Screw length 3/8 inch
$0.00
METAL SCREW HEX WASHER HEAD #14 X 3"
X14X3H
- A thread forming tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- Has an indented top surface, six flat sides with a flat washer which projects beyond the sides and provides a flat bearing surface.
- The washer and head are formed together as one piece. (Hex washer slotted head)
- Increased bearing area reduces likelihood of crushing mating surfaces.
- Zinc plated steel.
- Screw diameter 14
- Screw length 3 inches
$0.00
METRIC MACH. SCREW PHILLIPS PAN HD M4-0.70 X 8
XM4X8P
- A metric machine screw is a straight shank fastener with a metric thread pitch designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw.
- Machine screws form a fastening superior in strength to spaced thread screws.
- Metric screws are the type almost exclusively used in items manufactured in Europe.
- M4-.70 diameter.
- Length is 8 mm.
- Zinc plated.
- Normally class 4.8.
- Made from carbon steel.
- Pan head Phillips.
$0.00
TEK SCREW HEX WASHER HD #10 X 1"
10X1T
- A tapping screw with spaced threads and a drill point which drills its own hole.
- May be used to attach plywood, soft woods or composition board to metal, or attach metal to metal.
- All self-drilling screws offer economical benefits: reduces labor and tooling costs; reduces or eliminates drill bits and taps.
- Hex washer head.
- Steel zinc plated.
- Rockwell hardness C52 minimum.
- Diameter: 10
- Length: 1"
$0.00
TEK SCREW FLAT HEAD PHILLIPS #10 X 1"
X10X1FHPT
- A tapping screw with spaced threads and a drill point which drills its own hole
- May be used to attach plywood, soft woods or composition board to metal, or attach metal to metal
- All self-drilling screws offer economical benefits: reduces labor and tooling costs; reduces or eliminates drill bits and taps
- Flat head phillips head
- Steel zinc plated
$0.00
METAL SCREW PAN HEAD PHILLIPS
X4X1P
- A thread forming tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- Phillips Pan Head
- For general applications.
- Can be substituted in most applications for round, truss or binding screws.
- Steel zinc plated.
- Diameter: 4
- Length: 1"
$0.00
SHEET METAL SCREW PHIL PAN HD #14 X 1-1/4" STAINLESS
X14X114PSS
- A thread forming stainless tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- Pan heads have a rounded top surface, cylindrical sides and a flat bearing surface.
- For general applications.
- Can be substituted in most applications for round, truss or binding screws.
$0.00
DRYWALL SCREW - FINE #10 X 4"
X10X4DW
- A bugle head screw with spaced threads, extra sharp point and black phosphate finish.
- Used to attach drywall to woods studs or 25 gauge metal studs.
- Heat treated steel material.
- Minimum Rockwell C 44 hardness.
- Screw diameter: 10
- Length 4 inches
- Bugle head, phillips drive
$0.00
MACHINE SCREW HEX HEAD TYP-F 1/4"-20 X 1-1/2" THREAD CUTTING
X1420X112HTYF
- A thread cutting screw with machined screw thread pitch, blunt point, tapered entering threads and multiple cutting edges.
- Steel thread-cutters are used in heavy gauge sheet metal, aluminum, zinc and lead die castings, cast iron, brass and plastic.
- When using any thread-cutting screw, the material in which the threads are cut should have a lower hardness by at least 10 to 20 Rockwell hardness points.
- Made from zinc plated AISI 1016-1024 steel or equivalent.
- Type F thread cutting style.
- Hex washer slotted head.
- 1/4-20 diameter.
- Length of 1-1/2".
$0.00
MACHINE SCREW TORX PAN HD #10-24 X 1-1/2" STAINLESS
X1024X112PTXSS
- A straight shank fastener with external threads designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw.
- Machine screws form a fastening superior in strength to spaced thread screws.
$0.00
MACHINE SCREW PHILLIPS PAN HD 1/4"-20 X 1/2"
1420X12
- A straight shank fastener with external threads designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw.
- Machine screws form a fastening superior in strength to spaced thread screws.
- Made from AISI 1006-1022 or equivalent steel.
- Pan head Phillips.
- Zinc plated steel.
- 1/4-20 diameter.
- Length of 1/2".
$0.00
TEK SCREW PHILLIPS PAN HEAD #8 X 1", STAINLESS
X8X1PTS
- A tapping screw with spaced threads and a drill point which drills its own hole.
- May be used to attach plywood, soft woods or composition board to metal, or attach metal to metal.
- All self-drilling screws offer economical benefits: reduces labor and tooling costs; reduces or eliminates drill bits and taps.
- Phillips pan head.
- Stainless Steel
$0.00
TEK SCREW PHILLIPS PAN HEAD #10 X 1/2", STAINLESS
X10X12PTS
- A tapping screw with spaced threads and a drill point which drills its own hole.
- May be used to attach plywood, soft woods or composition board to metal, or attach metal to metal.
- All self-drilling screws offer economical benefits: reduces labor and tooling costs; reduces or eliminates drill bits and taps.
- Phillips pan head.
- Stainless Steel
$0.00
METAL SCREW PAN HEAD PHILLIPS #4 X 3/4"
X4X34P
- A thread forming tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- Phillips Pan Head
- For general applications.
- Can be substituted in most applications for round, truss or binding screws.
- Steel zinc plated.
- Diameter: 4
- Length: 3/4"
$0.00
MACHINE SCREW TORX PAN HD #10-24 X 3/4" STAINLESS
X1024X34PTXSS
- A straight shank fastener with external threads designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw.
- Machine screws form a fastening superior in strength to spaced thread screws.
$0.00