Retaining Rings
RETAINING/SNAP RING EXTERNAL, 3/4"
ERR34
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 3/4".
$0.00
RETAINING/SNAP RING EXTERNAL, 7/16"
ERR76
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 7/16".
$0.00
RETAINING/SNAP RING INTERNAL, 3/8"
IRR38
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 3/8".
$0.00
E-CLIP, RETAINING 7/16" SHAFT
EC76
- Stamped clips for deep grooves with three prongs that yield high thrust load capacity.
- Designed for radial installation into machined grooves on shafts of varying diameter.
- E clips require a deeper groove, but provide exceptional thrust loadings when compared to fasteners of the same size and weight.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 7/16".
$0.00
RETAINING/SNAP RING EXTERNAL, 3/8"
ERR38
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 3/8".
$0.00
RETAINING/SNAP RING INTERNAL, 3/4"
IRR34
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 3/4".
$0.00
E-CLIP, RETAINING 1/8" SHAFT
EC18
- Stamped clips for deep grooves with three prongs that yield high thrust load capacity.
- Designed for radial installation into machined grooves on shafts of varying diameter.
- E clips require a deeper groove, but provide exceptional thrust loadings when compared to fasteners of the same size and weight.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 1/8".
$0.00
E-CLIP, RETAINING 5/8" SHAFT
EC58
- Stamped clips for deep grooves with three prongs that yield high thrust load capacity.
- Designed for radial installation into machined grooves on shafts of varying diameter.
- E clips require a deeper groove, but provide exceptional thrust loadings when compared to fasteners of the same size and weight.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 5/8".
$0.00
RETAINING/SNAP RING INTERNAL, 1/2"
IRR50
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 1/2".
$0.00
RETAINING/SNAP RING INTERNAL, 7/16"
IRR76
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 7/16".
$0.00